User Tools
использование_протоколов_маршрутизации
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
использование_протоколов_маршрутизации [2022/03/15 15:17] val [Подготовка UNIX] |
использование_протоколов_маршрутизации [2024/12/06 20:24] (current) val |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| <code> | <code> | ||
| - | gate.isp.un# route add 192.168.100+X/24 172.16.1.X | + | gate.isp.un# ip route add 192.168.100+X.0/24 via 172.16.1.X |
| </code> | </code> | ||
| ==== Настройка маршрутизатора cisco ==== | ==== Настройка маршрутизатора cisco ==== | ||
| Line 26: | Line 26: | ||
| ==== Подготовка UNIX ==== | ==== Подготовка UNIX ==== | ||
| - | * [[Сервисы Gateway и routing#Протокол OSPF]] - установка и базовая настройка ПО | + | * [[Сервисы Gateway и routing#Протокол OSPF]] - установка и базовая настройка и запуск |
| <code> | <code> | ||
| Line 52: | Line 52: | ||
| <code> | <code> | ||
| - | server### ifdown eth0 | + | linux# ###telnet localhost ospfd |
| - | server# telnet localhost ospfd | + | linux# vtysh |
| </code><code> | </code><code> | ||
| router ospf | router ospf | ||
| network 192.168.X.0/24 area 0 | network 192.168.X.0/24 area 0 | ||
| redistribute connected | redistribute connected | ||
| - | </code> | ||
| - | <code> | ||
| - | server# telnet localhost ospfd | ||
| </code><code> | </code><code> | ||
| - | ! access-list ACL_IP_NET permit 192.168.100+X.0/24 | + | frr# show ip ospf neighbor |
| - | + | ||
| - | ! route-map RM_IP_NET permit 1 | + | |
| - | ! match ip address ACL_IP_NET | + | |
| - | + | ||
| - | router ospf | + | |
| - | network 192.168.X.0/24 area 0 | + | |
| - | redistribute connected ! route-map RM_IP_NET | + | |
| - | service_ospfd# show ip ospf neighbor | + | frr# show ip route |
| </code><code> | </code><code> | ||
| linux# ip r | linux# ip r | ||
| - | |||
| - | freebsd# netstat -rn | ||
| - | |||
| - | server# telnet localhost zebra | ||
| - | </code><code> | ||
| - | service_zebra# show ip route | ||
| </code> | </code> | ||
| Line 87: | Line 71: | ||
| ==== Cisco ==== | ==== Cisco ==== | ||
| <code> | <code> | ||
| + | no router ospf 100 | ||
| + | |||
| router bgp 100+X | router bgp 100+X | ||
| neighbor 192.168.X.10 remote-as 200+X | neighbor 192.168.X.10 remote-as 200+X | ||
| Line 92: | Line 78: | ||
| </code> | </code> | ||
| - | ==== Zebra ==== | + | ==== frr ==== |
| - | + | ||
| - | * [[https://docstore.mik.ua/manuals/ru/LARTC/x3036.html|Настройка BGP4 с помощью Zebra]] | + | |
| <code> | <code> | ||
| - | # cat /etc/quagga/bgpd.conf | + | # cat /etc/frr/daemons |
| </code><code> | </code><code> | ||
| - | hostname service_bgpd | + | ... |
| - | password zebra | + | bgpd=yes |
| - | enable password zebra | + | ... |
| + | </code><code> | ||
| + | # service frr restart | ||
| + | # vtysh | ||
| + | </code><code> | ||
| router bgp 200+X | router bgp 200+X | ||
| - | redistribute connected | + | no bgp ebgp-requires-policy |
| neighbor 192.168.X.1 remote-as 100+X | neighbor 192.168.X.1 remote-as 100+X | ||
| + | redistribute connected | ||
| </code> | </code> | ||
| - | ==== Cisco/Zebra ==== | + | ==== Cisco/frr ==== |
| <code> | <code> | ||
| # show ip bgp summary | # show ip bgp summary | ||
| + | |||
| + | # show ip route | ||
| </code> | </code> | ||
использование_протоколов_маршрутизации.1647346665.txt.gz · Last modified: 2022/03/15 15:17 by val
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
