User Tools
использование_протокола_802.1q
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
использование_протокола_802.1q [2021/07/26 10:14] admin [Debian/Ubuntu] |
использование_протокола_802.1q [2022/03/26 06:37] val [Настройка интерфейсов] |
||
|---|---|---|---|
| Line 37: | Line 37: | ||
| ==== Настройка интерфейсов ==== | ==== Настройка интерфейсов ==== | ||
| <code> | <code> | ||
| + | !!!switch1# | ||
| conf terminal | conf terminal | ||
| + | |||
| + | interface FastEthernet0/1 | ||
| + | ! desc linux server | ||
| + | ! switchport trunk encapsulation dot1q ! для старых серий, в GNS3 не нужно | ||
| + | switchport mode trunk | ||
| interface FastEthernet0/2 | interface FastEthernet0/2 | ||
| - | ! desc win client1 | + | ! desc windows client1 |
| switchport mode access | switchport mode access | ||
| switchport access vlan 2 | switchport access vlan 2 | ||
| ! spanning-tree portfast | ! spanning-tree portfast | ||
| - | interface FastEthernet0/1 | + | |
| - | ! desc Linux | + | ! ИЛИ |
| - | ! switchport trunk encapsulation dot1q | + | |
| - | switchport mode trunk | + | |
| + | !interface FastEthernet0/2 | ||
| + | ! desc uplink to switch3 | ||
| + | ! switchport mode trunk | ||
| + | |||
| + | !!!switch3# | ||
| + | !interface Port-channel1 | ||
| + | ! desc uplink to CORE (switch1 and switch2) | ||
| + | ! switchport mode trunk | ||
| + | |||
| + | !interface FastEthernet0/2 | ||
| + | ! desc windows client1 | ||
| + | ! switchport mode access | ||
| + | ! switchport access vlan 2 | ||
| </code> | </code> | ||
| ===== Настройка Linux системы ===== | ===== Настройка Linux системы ===== | ||
| - | ==== Debian/Ubuntu ==== | + | !!! При использовании в системе docker потребовалась перезагрузка |
| <code> | <code> | ||
| - | root@server:~# cat /etc/sysctl.conf | + | linuxgate# cat /etc/sysctl.conf |
| </code><code> | </code><code> | ||
| ... | ... | ||
| Line 62: | Line 82: | ||
| </code><code> | </code><code> | ||
| # sysctl -f | # sysctl -f | ||
| + | </code> | ||
| + | ==== Debian ifupdown ==== | ||
| + | |||
| + | <code> | ||
| root@server:~# apt install vlan | root@server:~# apt install vlan | ||
| Line 74: | Line 98: | ||
| mtu 1500 | mtu 1500 | ||
| vlan_raw_device eth1 | vlan_raw_device eth1 | ||
| - | # vlan_raw_device eth0 | + | # vlan_raw_device bond0 |
| </code><code> | </code><code> | ||
| root@server:~# ifup vlan2 | root@server:~# ifup vlan2 | ||
| Line 81: | Line 105: | ||
| root@server:~# vconfig rem vlan2 | root@server:~# vconfig rem vlan2 | ||
| Removed VLAN -:vlan2:- | Removed VLAN -:vlan2:- | ||
| + | </code> | ||
| + | |||
| + | ==== Ubuntu netplan ==== | ||
| + | |||
| + | * [[https://itproffi.ru/nastrojka-seti-cherez-netplan-v-ubuntu-17-10-i-vyshe/|Настройка сети через Netplan в Ubuntu 17.10 и выше]] | ||
| + | |||
| + | <code> | ||
| + | server# cat /etc/netplan/01-netcfg.yaml | ||
| + | </code><code> | ||
| + | ... | ||
| + | vlans: | ||
| + | vlan2: | ||
| + | id: 2 | ||
| + | link: bond0 | ||
| + | addresses: [192.168.100+X.1/24] | ||
| + | </code><code> | ||
| + | server# netplan apply | ||
| </code> | </code> | ||
использование_протокола_802.1q.txt · Last modified: 2022/03/26 06:37 by val
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
