Differences

This shows you the differences between two versions of the page.

--- плата_openvox_d130 [2018/02/02 09:45]
val
+++ плата_openvox_d130 [2023/05/24 08:39] (current)
val
@@ Line 1: / Line 1: @@
 ====== Плата OpenVox D130 ======
+  * [[https://ru.wikipedia.org/wiki/%D0%A6%D0%B8%D1%84%D1%80%D0%BE%D0%B2%D0%BE%D0%B9_%D0%BF%D0%BE%D1%82%D0%BE%D0%BA_E1|Цифровой поток E1]]
+  * [[http://docs.tzafrir.org.il/dahdi-tools/README.html|DAHDI Telephony Interface Driver]]
   * [[http://www.openvox.cn/products/telephony-cards/digital-cards/157-d130-series|OpenVox D130 Series]]
   * [[http://www.openvox.cn/pub/documents/manuals/D130P_DE130P_on_DAHDI_User_Manual.pdf|D130P_DE130P_on_DAHDI_User_Manual]]
   * [[http://asterisk-support.ru/question/57191/nastroika-openvox-d130pd130e/|Настройка OpenVox D130P/D130E]]
   * [[http://pinouts.ru/Net/cisco_rj45_e1.shtml|Cisco RJ45 E1 (T1) pinout]]
-  * [[https://asterisk-pbx.ru/wiki/asterisk/cf/chan_dahdi|Настройка DAHDI - chan_dahdi]]
 <code>
@@ Line 36: / Line 37: @@
   * [[Плата Digium TDM]]
+  * [[https://asterisk-pbx.ru/wiki/asterisk/cf/chan_dahdi|Настройка DAHDI - chan_dahdi]]
+Channels in DAHDI devices (such as DAHDI PCI cards) are groups to logical units called "spans" (for example: a port in a digital card is a span).
+span => <Number>,<Timing>,<Line BuildOut>,<Framing>,<Coding>[,Yellow]
+Timing:
+This determines how timing is handled by the card.
+  * 0 - Порт является источником синхронизации
+  * 1 - Получает синхронизацию с удаленной станции
+Line BuildOut:
+The line build-out (or LBO) is an integer, from the following table:
 <code>
-cat /etc/dahdi/system.conf
+: 0 db (CSU) / 0-133 feet (DSX-1)
+: 133-266 feet (DSX-1)
+: 266-399 feet (DSX-1)
+: 399-533 feet (DSX-1)
+: 533-655 feet (DSX-1)
+: -7.5db (CSU)
+: -15db (CSU)
+: -22.5db (CSU)
+</code>
+Framing:
+ccs - Common Channel Signaling (CCS) over a digital PRI. It is the transmission of signaling information out of the information band. ISDN Q.931 signaling is referred to as a CCS
+Coding:
+hdb3 - high density bipolar of order 3 - один из способов линейного кодирования, применяется при передаче данных на расстояние по цифровому каналу связи
+crc4: Cyclic redundancy check - алгоритм нахождения контрольной суммы, предназначенный для проверки целостности данных
+termtype: setting is for TE or NT (the default is TE), TE - cpe signallingget and get timing from the remote party, NT - provide timing to the remote party
+<code>
+# cat /etc/dahdi/system.conf
 </code><code>
-...
+# Autogenerated by /usr/sbin/dahdi_genconf on Wed Apr 25 10:11:25 2018
-span=1,1,0,ccs,hdb3,crc4
+# If you edit this file and execute /usr/sbin/dahdi_genconf again,
+# your manual changes will be LOST.
+# Dahdi Configuration File
+#
+# This file is parsed by the Dahdi Configurator, dahdi_cfg
+#
+# Span 1: D115/0/1 "D115 (E1/T1) Card 0 Span 1" (MASTER) CCS/HDB3/CRC4 ClockSource
+# span=1,1,0,ccs,hdb3,crc4
+span=1,1,0,ccs,hdb3
 # termtype: te
 bchan=1-15,17-31
 dchan=16
+alaw=1-15
+alaw=17-31
 echocanceller=mg2,1-15,17-31
-...
+# Global data
+loadzone        = ru
+defaultzone     = ru
 </code><code>
 # cat /etc/asterisk/dahdi-channels.conf
 </code><code>
 ...
-group=0,11
+;Порядок строк играет роль!!!
-context=from-pstn
+group=0
+context=default
 switchtype = euroisdn
 signalling = pri_cpe
+overlapdial=incoming
 channel => 1-15,17-31
-context = default
-group = 63
 ...
+</code><code>
+# dahdi_scan -vvvvv
+# dahdi_cfg -v
+</code>
+!!!! Иногда помогает "холодный" рестарт !!!!
+<code>
+# dahdi_scan -vvvvv
+# service asterisk restart
 </code><code>
 e1*CLI> dahdi show status
@@ Line 74: / Line 140: @@
 [from-pstn]
-exten => s,1,WaitExten()
+exten => _4XX,1,Goto(default,${EXTEN},1)
-exten => _XX,1,Goto(default,4${EXTEN},1)
+</code><code>
+e1*CLI> pri set debug on span 1
+...
 </code>

Методические материалы Лохтурова Вячеслава

User Tools

Site Tools

Differences

Page Tools